DiscImageChef Report for HP Ultrium 5-SCSI Z6ED

SCSI characteristics:
Vendor: HP
Product: Ultrium 5-SCSI
Revision: Z6ED
Device is connected and supported.
Sequential-access device
Device claims to comply with ANSI X3.408:2005 (SPC-4)
Device does not claim to comply with any SCSI ECMA standard
Device does not claim to comply with any SCSI ISO/IEC standard
Device is removable
Device supports protection information
Multi-port device
Device supports TCQ queue
Device only supports implicit assymetrical access
Device supports only ST clocking
Device complies with unknown standard code 0x8B00
Device complies with unknown standard code 0x200C
Device complies with unknown standard code 0x6204
Device complies with unknown standard code 0x0704
Device supports MODE SENSE (6)
Device supports MODE SENSE (10)
Device supports MODE SENSE subpages
Device uses a write cache

SCSI mode sense pages:
Mode Contents
MODE page 01h SCSI Read-write error recovery page:
Drive will use the most expedient form of error recovery first
Drive will repeat read operations 21 times
Drive will repeat write operations 10 times
MODE page 02h SCSI Disconnect-Reconnect mode page:
100 µs maximum permitted to assert BSY without a REQ/ACK handshake
Data transfer disconnect control is not used
MODE page 0Ah SCSI Control mode page:
Tasks aborted by other initiator's actions should be terminated with TASK ABORTED
The logical unit maintains separate task sets for each nexus
Commands should be sent strictly ordered
If ACA is established, the task set commands shall resume after it is cleared, otherwise they shall terminate with CHECK CONDITION
LUN shall clear unit attention condition reported in the same nexus
On medium insertion, it shall be loaded for full access
MODE page 0Ah subpage 01h SCSI Control extension page:
Timestamp can be initialized by methods outside of the SCSI standards, but SCSI's SET TIMESTAMP shall take precedence over them
Implicit Asymmetric Logical Unit Access is enabled
Initial priority is 0
MODE page 0Ah subpage F0h Unknown mode page
MODE page 0Fh SCSI Data compression page:
Drive supports data compression
Data compression is enabled with an unknown algorithm coded 1
Data decompression is enabled
Last data read was compressed with an unknown algorithm coded 1
Report exception on compression is set to 0
MODE page 10h SCSI Device configuration page:
Active format: 0
Active partition: 0
Write buffer shall have a full ratio of 0 before being flushed to medium
Read buffer shall have an empty ratio of 0 before more data is read from medium
Drive will delay 30000 ms before buffered data is forcefully written to the medium even before buffer is full
Medium supports block IDs
Drive will pre-read until buffer is full
Drive generates end-of-data
Drive uses default compression
MODE page 10h subpage 01h Unknown mode page
MODE page 11h SCSI medium partition page:
1 maximum additional partitions
0 additional partitions defined
Number and size of partitions can be manually defined
Partition parameters will not be applied until a FORMAT MEDIUM command is received
Device may erase any or all partitions on MODE SELECT for partitioning
Partitions are defined in units of 1000000000 bytes
Device is capable of recognizing both medium partitions and format
Medium has defined 2 partitions
Partition 0 is 1500 units of 1000000000 bytes long
Partition 1 runs for rest of medium
MODE page 18h Unknown mode page
MODE page 19h Unknown mode page
MODE page 19h subpage 01h Unknown mode page
MODE page 19h subpage 02h Unknown mode page
MODE page 19h subpage 03h Unknown mode page
MODE page 1Ah SCSI Power condition page:
Drive will not enter standy mode
Drive will not enter idle mode
MODE page 1Ch SCSI Informational exceptions control page:
Informational exceptions are disabled
MODE page 1Dh SCSI Medium Configuration Mode Page:
Drive allows a tape header to be overwritten
Drive allows any number of filemarks immediately preceding EOD to be overwritten except filemark closes to BOP
MODE page 3Ch Unknown mode page
MODE page 3Dh Unknown mode page
MODE page 3Eh Unknown mode page

SCSI extended vital product data pages:
EVPD Contents
EVPD page 00h Undecoded
EVPD page 83h SCSI Device identification:
Identifier belongs to addressed logical unit
NAA: 00:00:00:00:00:00:00:00
Identifier belongs to target port
Descriptor referes to Serial Attachment SCSI protocol
NAA: 00:00:00:00:00:00:00:00
Identifier belongs to target port
Descriptor referes to Serial Attachment SCSI protocol
Relative target port identifier: 0
Identifier belongs to target port
Descriptor referes to Serial Attachment SCSI protocol
Target group identifier: 0
Identifier belongs to target device that contains the addressed logical unit
Descriptor referes to Serial Attachment SCSI protocol
NAA: 00:00:00:00:00:00:00:00
Identifier belongs to target device that contains the addressed logical unit
Descriptor referes to Serial Attachment SCSI protocol
Inquiry descriptor contains:
EVPD page 85h SCSI Management Network Addresses:
There are no addresses
EVPD page 86h SCSI Extended INQUIRY Data:
Logical unit supports logical block protection
Device supports the SIMPLE task attribute
Device clears any unit attention condition in all LUNs after reporting for any LUN
EVPD page 87h Undecoded
EVPD page 88h Undecoded
EVPD page 90h Undecoded
EVPD page B0h SCSI Sequential-access Device Capabilities:
Device supports WORM media
EVPD page B1h Undecoded
EVPD page B2h TapeAlert Supported Flags Bitmap: 0xFEFFFFFFFE007FF0
EVPD page B3h Undecoded
EVPD page B4h
EVPD page C0h Undecoded
EVPD page C1h Undecoded
EVPD page C2h Undecoded
EVPD page C3h Undecoded
EVPD page C4h Undecoded
EVPD page CCh Undecoded
EVPD page D0h Undecoded