DiscImageChef Report for TOSHIBA MG03SCA400 DG02

SCSI characteristics:
Vendor: TOSHIBA (Toshiba Japan)
Product: MG03SCA400
Revision: DG02
Device is connected and supported.
Direct-access device
Device claims to comply with ANSI X3.408:2005 (SPC-4)
Device does not claim to comply with any SCSI ECMA standard
Device does not claim to comply with any SCSI ISO/IEC standard
Device supports LUN hierarchical addressing
Multi-port device
Device supports TCQ queue
Device does not support assymetrical access
Device supports only ST clocking
Device supports MODE SENSE (6)
Device supports MODE SENSE (10)
Device supports MODE SENSE subpages
Drive supports DPO and FUA bits

Device has 0 blocks of 512 bytes each
Device size: 0 bytes, 0 Mb, 0.00 MiB
Medium type code: 00h
Long block size: 640 bytes
Device supports READ CAPACITY (10) command.
Device supports READ (6) command.
Device supports READ (10) command.
Device supports READ (12) command.
Device supports READ (16) command.
Device supports READ LONG (10) command.

SCSI mode sense pages:
Mode Contents
MODE page 01h SCSI Read-write error recovery page:
Parameters can be saved
Automatic write reallocation is enabled
Automatic read reallocation is enabled
Drive will repeat read operations 63 times
Drive will repeat write operations 63 times
Drive will employ a maximum of 8000 ms to recover data
MODE page 02h SCSI Disconnect-Reconnect mode page:
Parameters can be saved
1000 µs maximum permitted to assert BSY without a REQ/ACK handshake
Data transfer disconnect control is not used
MODE page 03h SCSI Format device page:
Parameters can be saved
520 tracks per zone to use in dividing the capacity for the purpose of allocating alternate sectors
0 sectors per zone that shall be reserved for defect handling
0 tracks per zone that shall be reserved for defect handling
100 tracks per LUN that shall be reserved for defect handling
3169 physical sectors per track
512 Bytes per physical sector
Target-dependent interleave value is 1
760 sectors between last block of one track and first block of the next
308 sectors between last block of a cylinder and first block of the next one
Drive supports hard-sectoring format
Sector addressing is progressively incremented in one cylinder before going to the next
MODE page 04h SCSI Rigid disk drive geometry page:
Parameters can be saved
10 heads
328806 cylinders
Write pre-compensation starts at cylinder 0
Write current reduction starts at cylinder 0
Heads park in cylinder 0
Medium rotates at 7200 rpm
Spindle synchronization is disable or unsupported
MODE page 07h SCSI Verify error recovery page:
Parameters can be saved
Drive will repeat verify operations 63 times
Drive will employ a maximum of 8000 ms to recover data
MODE page 08h SCSI Caching mode page:
Parameters can be saved
Drive does not distinguish between cached read data
Drive does not distinguish between cached write data
Pre-fetch will be done for READ commands of 65535 blocks or less
A maximum of 65535 blocks will be pre-fetched even if it is commanded to pre-fetch more
Pre-fetch can continue across discontinuities (such as cylinders or tracks)
Drive should not reorder the sequence of write commands to be faster
Drive should have 8 cache segments
MODE page 0Ah SCSI Control mode page:
Parameters can be saved
The logical unit maintains one task set for all nexuses
Commands should be sent strictly ordered
If ACA is established, the task set commands shall resume after it is cleared, otherwise they shall terminate with CHECK CONDITION
LUN shall clear unit attention condition reported in the same nexus
On medium insertion, it shall be loaded for full access
A maximum of 3068700 ms are allowed to remain busy
MODE page 18h Unknown mode page
MODE page 19h Unknown mode page
MODE page 19h subpage 01h Unknown mode page
MODE page 19h subpage 02h Unknown mode page
MODE page 19h subpage 03h Unknown mode page
MODE page 1Ah SCSI Power condition page:
Parameters can be saved
Drive will not enter standy mode
Idle timer A is set to 2000 ms
Idle timer B is set to 600000 ms
Performing background functions take precedence over maintaining low power conditions
MODE page 1Ch SCSI Informational exceptions control page:
Parameters can be saved
Informational exceptions are enabled
Only report informational exception condition on request
Drive shall log informational exception conditions
Timer interval is 600000 ms
Background functions are enabled
MODE page 1Ch subpage 01h SCSI Background Control page:
Parameters can be saved
Background medium scans are enabled
24 hours shall be between the start of a background scan operation and the next
At least 250 ms must be idle before resuming a suspended background scan operation
At most 2000 ms must be before suspending a background scan operation and processing received commands
MODE page 21h Unknown mode page

SCSI extended vital product data pages:
EVPD Contents
EVPD page 00h Undecoded
EVPD page 83h SCSI Device identification:
Identifier belongs to addressed logical unit
NAA: 50:00:03:95:38:E0:BD:F4
Identifier belongs to target port
Descriptor referes to Serial Attachment SCSI protocol
NAA: 50:00:03:95:38:E0:BD:F6
Identifier belongs to target port
Descriptor referes to Serial Attachment SCSI protocol
Relative target port identifier: 1
Identifier belongs to target device that contains the addressed logical unit
Descriptor referes to Serial Attachment SCSI protocol
NAA: 50:00:03:95:38:E0:BD:F5
Identifier belongs to target device that contains the addressed logical unit
Descriptor referes to Serial Attachment SCSI protocol
SCSI name string identifier: naa.5000039538E0BDF5
EVPD page 86h SCSI Extended INQUIRY Data:
Logical unit supports type 1 protection
Device supports head of queue
Device supports the ORDERED task attribute
Device supports the SIMPLE task attribute
Device supports marking a block as uncorrectable with WRITE LONG
Device supports disabling correction with WRITE LONG
Device has a volatile cache
Extended self-test takes 08:32:00 to complete
EVPD page 8Ah Undecoded
EVPD page 90h Undecoded
EVPD page B1h Undecoded
EVPD page DCh Undecoded